Description

Overview

The TP-Link CPE510 is a 5 GHz outdoor CPE built for one job: carrying a wireless link across a long distance where running a cable is not practical. It is a point-to-point wireless bridge with a built-in 13 dBi directional antenna, rated by TP-Link for links of 15 km or more with a clear line of sight. It is not there to serve phones and laptops directly — it joins two buildings, two sites, or a remote camera or office back to the main network, over the air.

Inside, a Qualcomm Atheros 560 MHz processor with 64 MB of DDR2 memory and 8 MB of flash drives 802.11a/n on the 5 GHz band, up to 300 Mbps on a 40 MHz channel. The 2×2 directional MIMO antenna focuses the signal into a 45-degree horizontal and 30-degree elevation beam, which is what makes a 15 km link possible. The ASA plastic enclosure is rated IPX5 with 15 kV ESD and 6 kV lightning protection, it runs from -40 °C to 70 °C, and a 24 V 0.5 A passive PoE adapter is included, with a PoE run of up to 60 metres. Be clear on one point: this v3 hardware has a single 10/100 Mbps shielded Ethernet port — not Gigabit, and no PoE passthrough.

Key Benefits

The first benefit is distance. A 15 km+ link lets a small ISP, a farm, a factory or a school with a second campus connect two sites without a leased line or a fibre trench. Two CPE510 units pointed at each other carry the connection, and TP-Link’s MAXtream TDMA keeps the link stable by scheduling when each side talks.

The second benefit is a clean band and a low total cost. The CPE510 works on 5.15 to 5.85 GHz with DFS, far from the crowded 2.4 GHz band, so the link holds up in the real world. And the box holds everything the job needs, with no separate injector, no enclosure and no subscription to buy.

Finally, it is flexible. It works as an access point, a client, a bridge, a repeater, an AP router or an AP client router for WISP use, so one model on the shelf covers several kinds of jobs. It is fanless, draws at most 9.8 W, and stays on a pole through rain, dust and heat.

Features and Advantages

The CPE510 runs on TP-Link’s Pharos platform. The PharOS web interface is built for outdoor wireless work, with signal strength, link quality and alignment tools that make aiming the antenna far less guesswork. Pharos Control manages several links from one place, and SNMP v2c, SSH and HTTP/HTTPS access are included.

Security is handled properly for an outdoor device. It supports WPA and WPA2 with WPA-PSK/WPA2-PSK (AES/TKIP), 64/128/152-bit WEP for older equipment, and multi-SSID with VLAN support in AP mode, so traffic can be split into separate networks.

The 224 × 79 × 60 mm enclosure is compact for a 13 dBi unit, built from ASA plastic that holds up better under constant sun than ordinary ABS. The included 24 V 0.5 A passive PoE adapter feeds power over the same cable as the data (pins 4 and 5 positive, 7 and 8 negative, 16–27 VDC), and its remote reset function lets the unit be power-cycled from the ground. One honest note: the wireless speed is up to 300 Mbps, but the wired port is 10/100 Mbps, so the Ethernet side tops out at 100 Mbps.

Ideal Users

The CPE510 suits anyone who needs to move a network connection across open space: WISPs connecting subscribers where fibre has not reached, a factory with a warehouse across the yard, a school with a second building, a farmhouse a kilometre from the main house. A camera on a gate needs no cable trench if a CPE510 carries its feed back to the recorder, and a site office can go up fast and come down again later.

It also suits businesses already running TP-Link Omada or Pharos equipment. What it does not suit is someone looking for an indoor Wi-Fi router — the directional antenna is a poor fit for serving a room full of phones. For indoor coverage, an access point like the TP-Link EAP225-Wall is the right tool, and the CPE510 can feed it.

Technical Specifications

Specification	Details
Model	TP-Link CPE510 (v3)
Wireless standard	IEEE 802.11a/n, 5 GHz
Wireless speed	Up to 300 Mbps (40 MHz); 144.4 Mbps (20 MHz); 72.2 Mbps (10 MHz); 36.1 Mbps (5 MHz)
Frequency	5.15–5.85 GHz
Antenna	13 dBi 2×2 dual-polarized directional MIMO; beamwidth 45° (H) / 30° (E)
Range	15 km+ (with MAXtream TDMA)
Modes	AP / Client / Bridge / Repeater / AP Router / AP Client Router (WISP)
Ethernet port	1× 10/100 Mbps shielded Ethernet (LAN0, Passive PoE in)
PoE	Passive PoE 16–27 VDC via LAN0 (+4, 5 pins; −7, 8 pins); 24 V 0.5 A adapter included; PoE up to 60 m
Max power consumption	9.8 W
Transmit power	0–23 dBm / 200 mW
Processor / memory	Qualcomm Atheros 560 MHz (MIPS 74Kc); 64 MB DDR2 RAM; 8 MB flash
Security	WPA/WPA2, WPA-PSK/WPA2-PSK (AES/TKIP), 64/128/152-bit WEP; multi-SSID with VLAN (AP mode); DFS; WDS
Management	Pharos Control, PharOS web UI, HTTP/HTTPS, SNMP v2c, SSH, Ping Watch Dog, DDNS
Enclosure	IPX5, ASA plastic; 15 kV ESD / 6 kV lightning protection; grounding terminal; reset button
Dimensions	224 × 79 × 60 mm
Operating temperature	−40 °C to 70 °C
Humidity	Operating 10–90% non-condensing; storage 5–95%
Certifications	CE, FCC, RoHS, IPX5
In the box	Outdoor Wireless CPE, 24 V 0.5 A Passive PoE Adapter, Pole Mounting Straps, AC Power Cord, Installation Guide

FAQs

Is the CPE510 a Wi-Fi router for home use?
No. It is an outdoor CPE and point-to-point bridge. Its directional antenna sends a focused signal in one direction over a long distance, not to cover a room. For indoor Wi-Fi, use an access point such as the TP-Link EAP225-Wall.

Do I need two CPE510 units for a point-to-point link?
Yes. A point-to-point link needs one unit at each end, aimed at each other with a clear line of sight. One unit alone works as an access point, client or repeater, but a bridge always needs a pair.

What is the real speed I will get?
The wireless rate is up to 300 Mbps on a 40 MHz channel, and the wired port is 10/100 Mbps, so the Ethernet side tops out at 100 Mbps.

Can it survive rain and heat in Pakistan?
It is built for it: IPX5 enclosure, -40 °C to 70 °C operating range, 15 kV ESD and 6 kV lightning protection with a grounding terminal. It still needs proper mounting and earthing.

Why Buy From NexGenShop.pk?

NexGenShop.pk lists the CPE510 at Rs 14,999 with the full box contents as TP-Link ships them — the CPE, the PoE adapter, the mounting straps and the power cord — so there is no surprise accessory to buy after the order arrives. The listing states the v3 specifications as published by TP-Link Pakistan, including the single 10/100 Mbps port. The team can be reached on Facebook and Instagram if you need help choosing a model. The CPE510 sold here is the v3 hardware, not a look-alike or an older revision. Pair it with the TP-Link EAP225-Outdoor for outdoor Wi-Fi at the far end, or feed an indoor access point such as the TP-Link EAP723 BE5000 Wi-Fi 7.

Final Conclusion

The TP-Link CPE510 is a focused tool, and that is its strength. It carries a 5 GHz wireless link across a long distance, through weather, with the PoE adapter and mounting hardware in the box. At Rs 14,999 it joins two sites without a leased line. Order it from NexGenShop.pk and get your remote site connected.